Free 2 Day Domestic
Free 2 day shipping for all domestic orders. Free Expedited shipping for all international orders over $399.
Due to Microsoft's discontinuation of updates, including security, certain functionality such as checkout and CAD may not work for you. We recommend using Google Chrome, Microsoft Edge, Firefox, or Safari to ensure full functionality.Thank you - the Ruland team
Dimensions | |||
---|---|---|---|
Bore (B1) Larger inner diameter. Should match nominal shaft diameter. |
25 mm |
Small Bore (B2) Smaller inner diameter. Should match nominal shaft diameter. |
16 mm |
Keyway (K1) |
8 mm |
Keyway (K2) |
5 mm |
B1 Max Shaft Penetration The maximum depth the shaft can penetrate into Bore B1. |
22.2 mm |
B2 Max Shaft Penetration The maximum depth the shaft can penetrate into Bore B2. |
22.2 mm |
Outer Diameter (OD) |
50.8 mm |
Bore Tolerance Variance in finished bore range before installation. |
+0.03 mm / -0.00 mm |
Length (L) |
46.1 mm |
Hub Width (LH) |
20.55 mm |
Recommended Shaft Tolerance Acceptable variance in nominal shaft diameter before performance loss. |
+0.000 mm / -0.013 mm |
||
Fastening Hardware | |||
Forged Clamp Screw Inch or metric socket head cap screw size. |
M5 |
Screw Material |
Alloy Steel |
Hex Wrench Size Wrench size that fits the screw head to tighten or loosen the screw. |
4.0 mm |
Screw Finish Surface finish and treatments on supplied hardware. |
Black Oxide |
Seating Torque Torque required to install supplied hardware. Use torque wrench for accurate seating torque. |
9.5 Nm |
Number of Screws |
2 ea |
Performance Specifications | |||
Dynamic Torque Reversing Max torque when coupling reverses direction without stopping. |
9.90 Nm |
Angular Misalignment Max angle of the shaft axes relative to each other. |
1.0° |
Dynamic Torque Non-Reversing Max torque for the coupling during quick changes in acceleration or deceleration. |
19.80 Nm |
Parallel Misalignment Shafts are parallel to each other, but not in-line with each other. They are offset. |
0.00 mm |
39.6 Nm |
Axial Motion The amount shafts can move closer to or away from each other. This is meant for thermal expansion of the shafts. No axial force can be placed on the coupling. |
0.32 mm |
|
Torsional Stiffness Measures the rigidity of the coupling. The more rigid the coupling, the less windup it will have. |
98.0 Nm/Deg |
Moment of Inertia |
7.257 x 10-5 kg-m2 |
Maximum Speed |
10,000 RPM |
Zero-Backlash? Zero-backlash ensures there is no loss of motion during operation. |
Yes |
Balanced Design The balanced design allows for reduced vibration at high RPMs. |
Yes |
||
Recommended Installation Tools | |||
Torque Wrench This torque wrench and bit combo is recommended to ensure proper installation. A torque wrench prevents the screw from being over torqued which can lead to product failure. |
Recommended Hex Key This hex key set has the appropriate hex key for product installation. Trained and experienced assemblers can use a hex key in place of a torque wrench. |
||
Full Bearing Support Required? Full bearing support is a bearing in close proximity to both sides of the coupling to prevent axial loads that could result in rapid coupling failure. |
Yes |
||
Additional Information | |||
Material Specification |
Hubs: 2024-T351 Aluminum Bar, Disc Springs: Type 302 Stainless Steel |
Temperature Minimum and maximum operating temperature. Operating temperature includes ambient temperature plus or minus factors such as system heat generated during operation, washdown, vacuum, etc... |
-40°F to 200°F (-40°C to 93°C) |
Sulfuric Anodized MIL-A-8625 Type II, Class 2 and ASTM B580 Type B Black Anodize |
Manufacturer |
Ruland Manufacturing |
|
Country of Origin |
USA |
Weight (lbs) |
0.425900 |
UPC |
634529204597 |
Tariff Code |
8483.60.8000 |
UNSPC Code used to identify products to standardize nomenclature around the world. |
31163008 |
||
Product Notes | |||
Note 1 |
Stainless steel hubs are available upon request. |
Note 2 |
Torque ratings are at maximum misalignment. |
Note 3 |
Performance ratings are for guidance only. The user must determine suitability for a particular application. |
Note 4 |
Torque ratings for the couplings are based on the physical limitations/failure point of the disc springs. Under normal/typical conditions the hubs are capable of holding up to the rated torque of the disc springs. In some cases, especially when the smallest standard bores are used or where shafts are undersized, slippage on the shaft is possible below the rated torque of the disc springs. Keyways are available to provide additional torque capacity in the shaft/hub connection when required. Please consult technical support for more assistance. |
|
|||
CERTIFICATIONS/STANDARDS | |||
---|---|---|---|
ISO 9001:2015 | Conflict Minerals | ||
RoHS3 | REACH | ||