JCC44-16-A JD44/70-92Y JC44-16-A
PRODUKTSPEZIFIKATIONEN

PRODUKTSPEZIFIKATIONEN
Abmessungen | |||
---|---|---|---|
Bohrung (B1) |
1,0000 zoll |
Bohrung (B2) |
1,0000 zoll |
Passfedernut (K1) |
1/4 zoll |
Passfedernut (K2) |
1/4 zoll |
Außendurchmesser (OD) |
2,750 zoll (69,9 mm) |
Länge (L) |
3,674 zoll (93,3 mm) |
Abmessungen | |||
---|---|---|---|
Bohrung (B1) |
1,0000 zoll |
Passfedernut (K) |
1/4 zoll |
Max. Nabentiefe (B1) |
1,300 zoll |
Außendurchmesser (OD) |
2,750 zoll (69,9 mm) |
Bohrungstoleranz |
+0,001 zoll / -0,000 zoll |
Nabenbreite (LH) |
1,300 zoll |
Länge (L) |
3,674 zoll (93,3 mm) |
Empfohlene Wellentoleranz |
+0,0000 zoll / -0,0005 zoll |
Key Width (K1) |
0.2500 in |
Key Height (K1) |
0.2500 in |
Keyway 1 Height (T1) |
1.1141 in |
Keyway 1 Width Tolerance |
+0.0020" / -0.0000" |
Keyway 1 Height Tolerance |
+0.0100" / -0.0000" |
||
Befestigungsschraube | |||
Innensechskantschraube |
M8 |
Anzahl der Schrauben |
je 1 |
Schraubenwerkstoff |
Legierter Stahl |
Schraubenoberfläche |
Brüniert |
Größe Sechskantschlüssel |
6,0 mm |
Anzugsmoment |
39 Nm |
Leistungsbeschreibungen | |||
Torque Specifications |
Torque ratings vary with insert selection |
Misalignment |
Misalignment ratings vary with insert selection |
Maximale Geschwindigkeit |
8.000 U/min |
Trägheitsmoment |
0.797 lb-in2 |
Bearing Support Required |
Ja |
Recommended Inserts |
|
spielfrei? |
Ja |
Ausgewogenes Design? |
Ja |
Fail Safe |
Ja |
||
zusätzliche Information | |||
Gewicht (kg) |
0.715924 |
Temperaturbereich |
23°C bis 82°C |
Materialspezifikation |
2024-T351 Aluminium Stangenmaterial |
Oberflächenverarbeitung |
Glänzend Poliert |
Spezifikation Oberflächenbehandlung |
Glänzend Poliert |
Hersteller |
Ruland Manufacturing |
Recommended Gap Between Hubs |
0,074 zoll (1,88 mm) |
Herkunftsland |
USA |
UPC |
65432939441 |
UNSPC |
31163011 |
Tariff Code |
8483.60.8000 |
||
Produkthinweise | |||
Anmerkung 1 |
Stainless steel hubs are available upon request. |
Anmerkung 2 |
Performance ratings are for guidance only. The user must determine suitability for a particular application. |
Anmerkung 3 |
Torque ratings for the couplings are based on the physical limitations/failure point of the spiders. Under normal/typical conditions the hubs are capable of holding up to the nominal torque of the spiders. Please consult technical support for more assistance. |
Prop 65 |
|
Abmessungen | |||
---|---|---|---|
Außendurchmesser (OD) |
2,750 zoll (69,9 mm) |
||
Leistungsbeschreibungen | |||
Nenndrehmoment |
300 zoll-lb (33,9 Nm) |
Winkelversatz |
0,9° |
Spitzen Drehmoment |
600 zoll-lb (67,79 Nm) |
Paralellversatz |
0,008 zoll (0,20 mm) |
Torsionssteife |
500 lb-zoll/Deg (56,49 Nm/Deg) |
Trägheitsmoment |
0.113995 lb-in2 (3.336 X 10-5 kg-m2) |
Axialbewegung |
0,060 zoll (1,52 mm) |
Maximale Geschwindigkeit |
8.000 U/min |
Bearing Support Required |
Ja |
spielfrei? |
Ja |
Approximate Assembly Force |
140 lbf |
Bearing Load at Max Parallel Misalignment |
65 lbf |
zusätzliche Information | |||
Gewicht (kg) |
0.128900 |
Temperaturbereich |
23°C bis 82°C |
Materialspezifikation |
Shorehärte 92 A Gelb Polyurethan |
Spezifikation Oberflächenbehandlung |
Poliert |
Hersteller |
Ruland Manufacturing |
UPC |
634529409077 |
Herkunftsland |
USA |
Tariff Code |
8483.60.8000 |
UNSPC |
31163011 |
||
Produkthinweise | |||
Anmerkung 1 |
Performance ratings are for guidance only. The user must determine suitability for a particular application. |
Anmerkung 2 |
Torque ratings for the couplings are based on the physical limitations/failure point of the spiders. Under normal/typical conditions the hubs are capable of holding up to the nominal torque of the spiders. In some cases especially when the smallest standard bores are used or where shafts are undersized slippage on the shaft is possible below the nominal torque of the spiders. Keyways are available to provide additional torque capacity in the shaft/hub connection when required. Please consult technical support for more assistance. |
Abmessungen | |||
---|---|---|---|
Bohrung (B1) |
1,0000 zoll |
Max. Nabentiefe (B1) |
1,300 zoll |
Außendurchmesser (OD) |
2,750 zoll (69,9 mm) |
Bohrungstoleranz |
+0,001 zoll / -0,000 zoll |
Nabenbreite (LH) |
1,300 zoll |
Länge (L) |
3,674 zoll (93,3 mm) |
Empfohlene Wellentoleranz |
+0,0000 zoll / -0,0005 zoll |
||
Befestigungsschraube | |||
Innensechskantschraube |
M8 |
Anzahl der Schrauben |
je 1 |
Schraubenwerkstoff |
Legierter Stahl |
Schraubenoberfläche |
Brüniert |
Größe Sechskantschlüssel |
6,0 mm |
Anzugsmoment |
39 Nm |
Leistungsbeschreibungen | |||
Torque Specifications |
Torque ratings vary with insert selection |
Misalignment |
Misalignment ratings vary with insert selection |
Maximale Geschwindigkeit |
8.000 U/min |
Trägheitsmoment |
0.798 lb-in2 |
Bearing Support Required |
Ja |
Recommended Inserts |
|
spielfrei? |
Ja |
Ausgewogenes Design? |
Ja |
Fail Safe |
Ja |
||
zusätzliche Information | |||
Gewicht (kg) |
0.692213 |
Temperaturbereich |
23°C bis 82°C |
Materialspezifikation |
2024-T351 Aluminium Stangenmaterial |
Oberflächenverarbeitung |
Glänzend Poliert |
Spezifikation Oberflächenbehandlung |
Glänzend Poliert |
Hersteller |
Ruland Manufacturing |
Recommended Gap Between Hubs |
0,074 zoll (1,88 mm) |
Herkunftsland |
USA |
UPC |
65432939427 |
UNSPC |
31163011 |
Tariff Code |
8483.60.8000 |
||
Produkthinweise | |||
Anmerkung 1 |
Stainless steel hubs are available upon request. |
Anmerkung 2 |
Performance ratings are for guidance only. The user must determine suitability for a particular application. |
Anmerkung 3 |
Torque ratings for the couplings are based on the physical limitations/failure point of the spiders. Under normal/typical conditions the hubs are capable of holding up to the nominal torque of the spiders. Please consult technical support for more assistance. |
Prop 65 |
|