JC50-16-A JD50/80-98R MJCC80-25-A
PRODUKTSPEZIFIKATIONEN
PRODUKTSPEZIFIKATIONEN
| Abmessungen | |||
|---|---|---|---|
|
Bohrung (B1) |
1,0000 zoll |
Bohrung (B2) |
25 mm |
|
Außendurchmesser (OD) |
3,125 zoll (79,4 mm) |
Länge (L) |
4,379 zoll (111,2 mm) |
| Abmessungen | |||
|---|---|---|---|
|
Bohrung (B1) |
1,0000 zoll |
Max. Nabentiefe (B1) |
1,590 zoll |
|
Außendurchmesser (OD) |
3,125 zoll (79,4 mm) |
Bohrungstoleranz |
+0,001 zoll / -0,000 zoll |
|
Nabenbreite (LH) |
1,590 zoll |
Länge (L) |
4,379 zoll (111,2 mm) |
|
Empfohlene Wellentoleranz |
+0,0000 zoll / -0,0005 zoll |
||
| Befestigungsschraube | |||
|
Innensechskantschraube |
M8 |
Anzahl der Schrauben |
je 1 |
|
Schraubenwerkstoff |
Legierter Stahl |
Schraubenoberfläche |
Brüniert |
|
Größe Sechskantschlüssel |
6,0 mm |
Anzugsmoment |
39 Nm |
| Leistungsbeschreibungen | |||
|
Torque Specifications |
Torque ratings vary with insert selection |
Misalignment |
Misalignment ratings vary with insert selection |
|
Maximale Geschwindigkeit |
8.000 U/min |
Trägheitsmoment |
1.625 lb-in2 |
|
Bearing Support Required |
Ja |
Recommended Inserts |
|
|
spielfrei? |
Ja |
Ausgewogenes Design? |
Ja |
|
Fail Safe |
Ja |
||
| zusätzliche Information | |||
|
Gewicht (kg) |
1.162485 |
Temperaturbereich |
23°C bis 82°C |
|
Materialspezifikation |
2024-T351 Aluminium Stangenmaterial |
Oberflächenverarbeitung |
Glänzend Poliert |
|
Spezifikation Oberflächenbehandlung |
Glänzend Poliert |
Hersteller |
Ruland Manufacturing |
|
Recommended Gap Between Hubs |
0,074 zoll (1,88 mm) |
Herkunftsland |
USA |
|
UPC |
65432939432 |
UNSPC |
31163011 |
|
Tariff Code |
8483.60.8000 |
||
| Produkthinweise | |||
|
Anmerkung 1 |
Stainless steel hubs are available upon request. |
Anmerkung 2 |
Performance ratings are for guidance only. The user must determine suitability for a particular application. |
|
Anmerkung 3 |
Torque ratings for the couplings are based on the physical limitations/failure point of the spiders. Under normal/typical conditions the hubs are capable of holding up to the nominal torque of the spiders. Please consult technical support for more assistance. |
Prop 65 |
|
WARNING This product can expose you to the chemical Ethylene Thiourea, known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to | Abmessungen | |||
|---|---|---|---|
|
Außendurchmesser (OD) |
3,125 zoll (79,4 mm) |
||
| Leistungsbeschreibungen | |||
|
Nenndrehmoment |
2.760 zoll-lb (311,84 Nm) |
Winkelversatz |
0,8° |
|
Spitzen Drehmoment |
5.520 zoll-lb (623,7 Nm) |
Paralellversatz |
0,008 zoll (0,20 mm) |
|
Torsionssteife |
1850 lb-zoll/Deg (209,02 Nm/Deg) |
Trägheitsmoment |
0.217711 lb-in2 (7.953 X 10-5 kg-m2) |
|
Axialbewegung |
0,060 zoll (1,52 mm) |
Maximale Geschwindigkeit |
8.000 U/min |
|
Bearing Support Required |
Ja |
spielfrei? |
Ja |
|
Approximate Assembly Force |
850 lbf |
Bearing Load at Max Parallel Misalignment |
85 lbf |
| zusätzliche Information | |||
|
Gewicht (kg) |
0.187700 |
Temperaturbereich |
23°C bis 82°C |
|
Materialspezifikation |
Shorehärte 98 A Rot Polyurethan |
Spezifikation Oberflächenbehandlung |
Poliert |
|
Hersteller |
Ruland Manufacturing |
UPC |
634529375976 |
|
Herkunftsland |
USA |
Tariff Code |
8483.60.8000 |
|
UNSPC |
31163011 |
||
| Produkthinweise | |||
|
Anmerkung 1 |
Performance ratings are for guidance only. The user must determine suitability for a particular application. |
Anmerkung 2 |
Torque ratings for the couplings are based on the physical limitations/failure point of the spiders. Under normal/typical conditions the hubs are capable of holding up to the nominal torque of the spiders. In some cases especially when the smallest standard bores are used or where shafts are undersized slippage on the shaft is possible below the nominal torque of the spiders. Keyways are available to provide additional torque capacity in the shaft/hub connection when required. Please consult technical support for more assistance. |
| Abmessungen | |||
|---|---|---|---|
|
Bohrung (B1) |
25 mm |
Passfedernut (K) |
8 mm |
|
Außendurchmesser (OD) |
3,125 zoll (79,4 mm) |
Bohrungstoleranz |
+0,03 mm / -0,00 mm |
|
Nabenbreite (LH) |
40,4 mm |
Länge (L) |
4,379 zoll (111,2 mm) |
|
Empfohlene Wellentoleranz |
+0,000 mm / -0,013 mm |
Key Width (K1) |
8 mm |
|
Key Height (K1) |
7 mm |
Keyway 1 Height (T1) |
28.3 mm |
|
Keyway 1 Width Tolerance |
+0.018 mm / -0.018 mm |
Keyway 1 Height Tolerance |
+0.2 mm / 0 mm |
| Befestigungsschraube | |||
|
Innensechskantschraube |
M8 |
Anzahl der Schrauben |
je 1 |
|
Schraubenwerkstoff |
Legierter Stahl |
Schraubenoberfläche |
Brüniert |
|
Größe Sechskantschlüssel |
6,0 mm |
Anzugsmoment |
39 Nm |
| Leistungsbeschreibungen | |||
|
Torque Specifications |
Torque ratings vary with insert selection |
Misalignment |
Misalignment ratings vary with insert selection |
|
Maximale Geschwindigkeit |
8.000 U/min |
Trägheitsmoment |
4.753-4 kg-m2 |
|
Bearing Support Required |
Ja |
Recommended Inserts |
|
|
spielfrei? |
Ja |
Ausgewogenes Design? |
Ja |
|
Fail Safe |
Ja |
||
| zusätzliche Information | |||
|
Gewicht (kg) |
1.159548 |
Temperaturbereich |
23°C bis 82°C |
|
Materialspezifikation |
2024-T351 Aluminium Stangenmaterial |
Oberflächenverarbeitung |
Glänzend Poliert |
|
Spezifikation Oberflächenbehandlung |
Glänzend Poliert |
Hersteller |
Ruland Manufacturing |
|
Recommended Gap Between Hubs |
Rating Coming Soon |
Herkunftsland |
USA |
|
UPC |
65432940706 |
UNSPC |
31163011 |
|
Tariff Code |
8483.60.8000 |
||
| Produkthinweise | |||
|
Anmerkung 1 |
Stainless steel hubs are available upon request. |
Anmerkung 2 |
Performance ratings are for guidance only. The user must determine suitability for a particular application. |
|
Anmerkung 3 |
Torque ratings for the couplings are based on the physical limitations/failure point of the spiders. Under normal/typical conditions the hubs are capable of holding up to the nominal torque of the spiders. Please consult technical support for more assistance. |
Prop 65 |
|
