MOST13-5/4.5D-A OD8/13-AT MOST13-3-A
PRODUCT SPECIFICATIONS

PRODUCT SPECIFICATIONS
Dimensions | |||
---|---|---|---|
Agujero (B1) |
5/4.5D mm |
Agujero (B2) |
3 mm |
Diámetro exterior OD |
12,7 mm (0,500 pulg) |
Longitud L |
15,9 mm (0,625 pulg) |
Dimensions | |||
---|---|---|---|
Agujero (B1) |
5/4.5D mm |
Parte plana (F) |
4,50 mm |
Flat Tolerance |
+.002”/-.000” |
Diámetro exterior OD |
12,7 mm (0,500 pulg) |
Penetración del eje máximo (B1) |
0,222 pulg |
Tolerancia del agujero |
+0,001 pulg / -0,000 pulg |
Ancho del cubo (LH) |
0,222 pulg |
Longitud L |
15,9 mm (0,625 pulg) |
Tolerancia del eje recomendada |
+0,000 mm / -0,013 mm |
||
Fastening Hardware | |||
Tornillo de fijación forjado |
M3 |
Número de tornillos |
1 cada |
Material del tornillo |
Alloy Steel |
Acabado de los tornillos |
Black Oxide |
Par de apriete |
0,92 Nm |
Tamaño de la llave hexagonal |
1,5 mm |
Performance Specifications | |||
Torque Specifications |
Torque ratings vary with insert selection |
Desalineación angular |
0,5° |
Desalineación paralela |
0,004 pulg (0,10 mm) |
Máxima desalineación paralela |
0,050 pulg (1,27 mm) |
Movimiento axial |
0,004 pulg (0,10 mm) |
Momento de inercia |
0.258 x 10-7 kg-m2 |
Velocidad máxima |
4.500 RPM |
Recommended Inserts |
|
Bearing Support Required |
sí |
¿Juego cero? |
Sí |
Mechanical Fuse |
Sí |
||
Additional Information | |||
UPC |
65432942066 |
País de origen |
EE.UU. |
Especificación de material |
Jaw and Oldham |
Acabado |
Black Anodized |
Especificación de acabado |
Anodizado con Sulfúrico MIL-A-8625 Tipo II, Clase 2 y ASTM B580 Tipo B Anodizado Negro |
Fabricante |
Ruland Manufacturing |
Temperatura |
Acetal -23°C a 65°C |
peso |
0.004052 |
Tariff Code |
8483.60.8000 |
UNSPC |
31163015 |
Product Notes | |||
Nota 1 |
"Performance ratings are for guidance only. The user must determine suitability for a particular application." |
Nota 2 |
"Torque ratings for the couplings are based on the physical limitations/failure point of the torque disks. Under normal/typical conditions the hubs are capable of holding up to the rated torque of the disks. In some cases` especially when the smallest standard bores are used or where shafts are undersized` slippage on the shaft is possible below the rated torque of the disks. Keyways are available to provide additional torque capacity in the shaft/hub connection when required. Please consult technical support for more assistance." |
Dimensions | |||
---|---|---|---|
Diámetro exterior OD |
12,7 mm (0,500 pulg) |
||
Performance Specifications | |||
Par recomendado |
6 pulg-lb (0,68 Nm) |
Par de rotura |
34 pulg-lb (3,9 Nm) |
Desalineación angular |
0,5° |
Desalineación paralela |
0,004 pulg (0,10 mm) |
Máxima desalineación paralela |
0,050 pulg (1,27 mm) |
Movimiento axial |
0,004 pulg (0,10 mm) |
Rigidez torsional |
13,9 lb-pulg/Deg (1,57 Nm/Deg) |
Momento de inercia |
0.00004 lb-in2 (1.171 X 10-8 kg-m2) |
Velocidad máxima |
4.500 RPM |
Bearing Support Required |
sí |
¿Juego cero? |
Sí |
Mechanical Fuse |
Sí |
Additional Information | |||
UPC |
634529059913 |
País de origen |
EE.UU. |
Especificación de material |
Acetal Disk |
Especificación de acabado |
Plain |
Fabricante |
Ruland Manufacturing |
Temperatura |
-23°C a 65°C |
peso |
0.000500 |
Tariff Code |
8483.60.8000 |
UNSPC |
31163015 |
||
Product Notes | |||
Nota 1 |
Performance ratings are for guidance only. The user must determine suitability for a particular application. |
Nota 2 |
Torque ratings for the couplings are based on the physical limitations/failure point of the torque disks. Under normal/typical conditions the hubs are capable of holding up to the rated torque of the disks. In some cases, especially when the smallest standard bores are used or where shafts are undersized, slippage on the shaft is possible below the rated torque of the disks. Keyways are available to provide additional torque capacity in the shaft/hub connection when required. Please consult technical support for more assistance. |
Prop. 65 |
|
||
Installation Instructions | |||
Instrucciones de instalación |
|
Video de instalación |
Dimensions | |||
---|---|---|---|
Agujero (B1) |
3 mm |
Diámetro exterior OD |
12,7 mm (0,500 pulg) |
Penetración del eje máximo (B1) |
5,6 mm |
Tolerancia del agujero |
+0,03 mm / -0,00 mm |
Ancho del cubo (LH) |
5,64 mm |
Longitud L |
15,9 mm (0,625 pulg) |
Tolerancia del eje recomendada |
+0,000 mm / -0,013 mm |
||
Fastening Hardware | |||
Tornillo de fijación forjado |
M3 |
Número de tornillos |
1 cada |
Material del tornillo |
Alloy Steel |
Acabado de los tornillos |
Black Oxide |
Par de apriete |
0,92 Nm |
Tamaño de la llave hexagonal |
1,5 mm |
Performance Specifications | |||
Torque Specifications |
Torque ratings vary with insert selection |
Desalineación angular |
0,5° |
Desalineación paralela |
0,004 pulg (0,10 mm) |
Máxima desalineación paralela |
0,050 pulg (1,27 mm) |
Movimiento axial |
0,004 pulg (0,10 mm) |
Momento de inercia |
4.478 x 10-8 kg-m2 |
Velocidad máxima |
4.500 RPM |
Recommended Inserts |
|
Bearing Support Required |
sí |
¿Juego cero? |
Sí |
Mechanical Fuse |
Sí |
||
Additional Information | |||
UPC |
634529065631 |
País de origen |
EE.UU. |
Especificación de material |
Jaw and Oldham |
Acabado |
Black Anodized |
Especificación de acabado |
Anodizado con Sulfúrico MIL-A-8625 Tipo II, Clase 2 y ASTM B580 Tipo B Anodizado Negro |
Fabricante |
Ruland Manufacturing |
Temperatura |
Acetal -23°C a 65°C |
peso |
0.002100 |
Tariff Code |
8483.60.8000 |
UNSPC |
31163015 |
Product Notes | |||
Nota 1 |
"Now available in stainless steel!" |
Nota 2 |
"Performance ratings are for guidance only. The user must determine suitability for a particular application." |
Nota 3 |
"Torque ratings for the couplings are based on the physical limitations/failure point of the torque disks. Under normal/typical conditions the hubs are capable of holding up to the rated torque of the disks. In some cases, especially when the smallest standard bores are used or where shafts are undersized, slippage on the shaft is possible below the rated torque of the disks. Keyways are available to provide additional torque capacity in the shaft/hub connection when required. Please consult technical support for more assistance." |
Prop. 65 |
|
Installation Instructions | |||
Instrucciones de instalación |
|
Video de instalación |