0,5000 pulg

1/8 pulg

0,467 pulg

25,4 mm (1,000 pulg)

+0,001 pulg / -0,000 pulg

0,467 pulg

35,3 mm (1,390 pulg)

+0,0000 pulg / -0,0005 pulg

M3

1 cada

Alloy Steel

Black Oxide

2,5 mm

2,1 Nm

Torque ratings vary with insert selection

Misalignment ratings vary with insert selection

8,000 RPM

0.004874 lb-in²

sí

JD16/25-98R, JD16/25-92Y, JD16/25-85B

Sí

Sí

Sí

0.013800

23°C a 82°C

Barra de aluminio 2024-T351

Bright

Bright, No Plating

Ruland Manufacturing

0,030 pulg (0,75 mm)

EE.UU.

634529111154

31163011

8483.60.8000

Stainless steel hubs are available upon request.

Performance ratings are for guidance only. The user must determine suitability for a particular application.

Torque ratings for the couplings are based on the physical limitations/failure point of the spiders. Under normal/typical conditions the hubs are capable of holding up to the nominal torque of the spiders. Please consult technical support for more assistance.

WARNING This product can expose you to the chemical Ethylene Thiourea, known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

1. Align the bores of the JCC16-8-A jaw coupling hubs on the shafts that are to be joined and determine if the misalignment parameters are within the limits of the coupling. (See spider for misalignment parameters.)
2. Fully tighten the M3 screw(s) on the first hub to the recommended seating torque of 2.1 Nm using a 2.5 mm hex torque wrench.
3. Insert a spider into the jaws of one hub until the raised points contact the base of the hub.
4. Insert the jaws of the second hub into the spider openings until the raised points contact the base of the second hub. Some force will be required to insert the second hub. This is normal.
5. Assure that a gap is maintained between the two hubs so there is no metal to metal contact. Fully tighten the screw(s) on the second hub to the recommended seating torque.

25,4 mm (1,000 pulg)

15 pulg-lb (1,70 Nm)

1,0°

30 pulg-lb (3,4 Nm)

0,006 pulg (0,15 mm)

9,3 lb-pulg/Deg (1,05 Nm/Deg)

0.00070 lb-in² (2.046 X 10^-7 kg-m²)

0,030 pulg (0,76 mm)

8,000 RPM

sí

Sí

0.002900

23°C a 82°C

Blue Spider

Plain

Ruland Manufacturing

634529069028

EE.UU.

8483.60.8000

31163011

0,030 pulg (0,75 mm)

Performance ratings are for guidance only. The user must determine suitability for a particular application.

Torque ratings for the couplings are based on the physical limitations/failure point of the spiders. Under normal/typical conditions the hubs are capable of holding up to the nominal torque of the spiders. In some cases, especially when the smallest standard bores are used or where shafts are undersized, slippage on the shaft is possible below the nominal torque of the spiders. Keyways are available to provide additional torque capacity in the shaft/hub connection when required. Please consult technical support for more assistance.

This product does not require a warning.

1. Align the bores of the jaw coupling hubs on the shafts that are to be joined and determine if the misalignment parameters are within the limits of the coupling.(Angular Misialignment: 1.0 deg, Parallel Misalignment: 0.006 in (0.15 mm), Axial Motion: 0.03 in (0.76 mm))
2. Fully tighten the screw(s) on the first hub to the recommended seating torque using a hex torque wrench.
3. Insert a spider into the jaws of the first hub until the raised points contact the base of the hub.
4. Insert the jaws of the second hub into the spider openings until the raised points contact the base of the second hub. Some force will be required to insert the second hub. This is normal.
5. Assure that a gap is maintained between the two hubs so there is no metal to metal contact. Fully tighten the screw(s) on the second hub to the recommended seating torque.

0,3750 pulg

0,467 pulg

25,4 mm (1,000 pulg)

+0,001 pulg / -0,000 pulg

0,467 pulg

35,3 mm (1,390 pulg)

+0,0000 pulg / -0,0005 pulg

M4

2 cada 90° de separación

Alloy Steel

Black Oxide

2,0 mm

2,2 Nm

Torque ratings vary with insert selection

Misalignment ratings vary with insert selection

8,000 RPM

0.005372 lb-in²

sí

JD16/25-98R, JD16/25-92Y, JD16/25-85B

Sí

Sí

Sí

0.016700

23°C a 82°C

Barra de aluminio 2024-T351

Bright

Bright, No Plating

Ruland Manufacturing

0,030 pulg (0,75 mm)

EE.UU.

634529068663

31163011

8483.60.8000

Stainless steel hubs are available upon request.

Performance ratings are for guidance only. The user must determine suitability for a particular application.

Torque ratings for the couplings are based on the physical limitations/failure point of the spiders. Under normal/typical conditions the hubs are capable of holding up to the nominal torque of the spiders. In some cases, especially when the smallest standard bores are used or where shafts are undersized, slippage on the shaft is possible below the nominal torque of the spiders. Keyways are available to provide additional torque capacity in the shaft/hub connection when required. Please consult technical support for more assistance.

WARNING This product can expose you to the chemical Ethylene Thiourea, known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

1. Align the bores of the JS16-6-A jaw coupling hubs on the shafts that are to be joined and determine if the misalignment parameters are within the limits of the coupling. (See spider for misalignment parameters.)
2. Fully tighten the M4 screw(s) on the first hub to the recommended seating torque of 2.2 Nm using a 2.0 mm hex torque wrench.
3. Insert a spider into the jaws of one hub until the raised points contact the base of the hub.
4. Insert the jaws of the second hub into the spider openings until the raised points contact the base of the second hub. Some force will be required to insert the second hub. This is normal.
5. Assure that a gap is maintained between the two hubs so there is no metal to metal contact. Fully tighten the screw(s) on the second hub to the recommended seating torque.